Setting up the Linksys Smart Wi-Fi Router is made easy using the Smart Setup Wizard. It is embedded in the firmware and is available even if the router does not have an Internet connection or is in its default settings.
This article will guide you on how to set up your Linksys Smart Wi-Fi Router using the Smart Setup Wizard.
QUICK TIP: The Smart Setup Wizard is supported by all Linksys Smart Wi-Fi Routers.
- You do not need a Setup CD or additional software to set up the router.
- You have the option to directly access the router’s web-based setup page during the setup process.
NOTE: The CD included in the packaging does not contain any setup software. It only contains your router’s documentation.
The following requirements should be met to avoid any problems during the setup:
- Browser requirements for the router setup and Linksys Smart Wi-Fi access:
- Microsoft Edge™
- Internet Explorer® 8 or higher
- Latest version of Chrome™ and Firefox®
- Safari® (for Mac® or iPad®)
- Latest Adobe Flash® Player
- Materials for setup – You should have the following items:
- Linksys Smart Wi-Fi Router
- One (1) or two (2) Internet / Ethernet (RJ-45) cables
- A wireless computer or a computer with an Ethernet port
- Active Internet connection – To check if you are able to access the Internet, connect the modem to the computer using an Ethernet cable as shown in the image below:
If your router came with external antennas, connect the antennas to the router first and then plug in the router to a power source. If your router has a power switch, make sure that the power switch is set to the | (ON) position. Wait until the power LED is solid.
Connect the Ethernet cable from your modem to the Internet port of the router.
Connect to your secured wireless network. You can locate the wireless credentials either at the bottom of the router or on the Quick Start Guide. To prevent any problems during setup, make sure you have a good signal from the router or bring the wireless computer closer to the same room as the router.
NOTE: If you are using a wired computer, skip Step 3 and proceed to Step 4.
Launch your web browser and enter “http://linksyssmartwifi.com” in the Address bar then press [Enter].
QUICK TIP: If you are unable to launch the Smart Setup, you can enter the default IP Address of the router, 192.168.1.1, or type myrouter.local in the browser’s Address bar.
Tick the checkbox beside I have read and accepted the License Terms for using this software then click Next to proceed.
- If the Smart Setup screen does not show up, press the Reset button at the back of the router for 10 seconds, turn the router OFF and then turn it back ON. Wait a few seconds for the router to boot up and start at Step 1 again.
- If no Internet connection is detected, the Your Internet cable is not connected correctly window will appear. Follow the suggested troubleshooting steps on the screen to resolve your connection problem then click Next.
For Digital Subscriber Line (DSL) users, the setup will prompt for the Point-to-Point Protocol over Ethernet (PPPoE) Account name and Password. Enter the necessary information then click Next to continue.
In the Updates for your router window, the Install future router updates automatically (recommended) is checked by default to allow automatic updates. You can uncheck it to control when to perform an Auto-Update. You can also enable this option again after you log into the router’s web-based setup page. Click Next to proceed.
Enter your desired Network Name and Network Password in the fields provided, and then click Next.
NOTE: You will have the same Network Name for both bands. The 5 GHz name however, will be appended with the _5GHz suffix. After the setup, you can individually customize the 5 GHz and 2.4 GHz Network Names through the router’s Wireless Tool. To know more about this feature, click here. If you do not wish to differentiate the 2.4 GHz from the 5 GHz band, tick the box beside Make all network names the same.
Enter a router password in the Create a router password field then click Next.
QUICK TIP: If your router displays an Add a password hint option, enter your preferred hint in the field provided. This will help you remember your router password in the future. Your password hint will only appear when you choose Local Access.
If you see the Your router is set up! message, this means that your router is now successfully set up. The new Wi-Fi settings as well as the router admin password will be displayed. Ensure that you write down the new settings in the fields provided on the Quick Start Guide for future reference. Click Next to complete the entire setup.
You will be redirected to the Create Your Linksys Smart Wi-Fi Account page for Remote Access. For instructions on how to create an account, click here. If you already have an account and you wish to associate it to your new router, click here.